In order to synchronize the operation of I/O ports with the internal 8-bit organization of the microcontroller, they are, similar to registers, grouped into five ports denoted by A, B, C, D and E. All of them have several features in common: • For practical reasons, many I/O pins are multifunctional. If a pin performs any of these functions, it may not be used as a general-purpose input/output pin. • Every port has its ‘satellite’, i.e. The corresponding TRIS register: TRISA, TRISB, TRISC etc.

Which determines the performance of port bits, but not their contents. By clearing any bit of the TRIS register (bit=0), the corresponding port pin is configured as an output.

Note the following details of the code protection. Adobe Illustrator Student Price Uk Rare. FlexROM, fuzzyLAB, In-Circuit Serial. PIC16F689 PIC16F690 1024 2048 4096.

Similarly, by setting any bit of the TRIS register (bit=1), the corresponding port pin is configured as an input. This rule is easy to remember 0 = Output, 1 = Input. RA0 = AN0 (determined by the ANS0 bit of the ANSELregister) RA1 = AN1 (determined by the ANS1 bit of the ANSELregister) RA2 = AN2 (determined by the ANS2 bit of the ANSELregister) RA3 = AN3 (determined by the ANS3 bit of the ANSELregister) RA5 = AN4 (determined by the ANS4 bit of the ANSELregister) Similar to bits of the TRISA register determine which of the pins are to be configured as inputs and which ones as outputs, the appropriate bits of the ANSEL register determine whether pins are to be configured as analog inputs or digital inputs/outputs. Each bit of this port has an additional function related to some of the built-in peripheral units, which will be described in later chapters.

This chapter covers only the RA0 pin’s additional function since it is related to port A and the ULPWU unit. Let's do it in mikroC. // The PORTA.2 pin is configured as a digital input. // All other PORTA pins are digital outputs ANSEL = ANSELH = 0; // All I/O pins are configured as digital PORTA = 0; // All PORTA pins are cleared TRISA = 0b00000100; // All PORTA pins except PORTA.2 are configured as outputs.

ULPWU UNIT The microcontroller is commonly used in devices which operate periodically and completely independently using a battery power supply. Minimum power consumption is one of the priorities here. Typical examples of such applications are: thermometers, fire detection sensors and the like. It is known that a reduction in clock frequency reduces the power consumption, thus one of the most convenient solutions to this problem is to slow down the clock, i.e.

To use 32KHz quartz crystal instead of 20MHz. The principle of operation is simple: A pin is configured as an output and a logic one (1) is brought to it. This causes the capacitor to be charged. Immediately after this, the same pin is configured as an input.

The change of logic state enables an interrupt and the microcontroller is set to Sleep mode. All that’s left now is to wait for the capacitor to discharge by the leakage current flowing out through the input pin. When it occurs, an interrupt takes place and the microcontroller proceeds with the program execution in normal mode. The whole procedure is repeated. Theoretically, this is a perfect solution.

The problem is that all pins able to cause an interrupt in this way are digital and have relatively large leakage current when their voltage is not close to the limit values Vdd (1) or Vss (0). In this case, the condenser is discharged for a short time since the current amounts to several hundreds of microamperes.

This is why the ULPWU circuit, capable of registering slow voltage drops with minimum power consumption, was designed. Its output generates an interrupt, while its input is connected to one of the microcontroller pins. It is the RA0 pin. Referring to figure (R=200 ohms, C=1nF), discharge time is approximately 30mS, while a total consumption of the microcontroller is 1000 times lower (several hundreds of nanoamperes). Similar to port A, a logic one (1) in the TRISB register configures the appropriate portB pin as an input and vice versa.

Six pins of this port can act as analog inputs (AN). When the X, Y and Z pins are configured as outputs set to logic one (1), it is only necessary to wait for an interrupt request which arrives upon any button press. After that, by combining zeros and ones on these outputs it is checked which push button is pressed. Let's do it in mikroC. /* The PORTB.1 pin is configured as a digital input. Any change of its logic state will cause an.i.n.terrupt.

It also has a pull-up resistor. All other PORTB pins are digital outputs.*/ ANSEL = ANSELH = 0; // All I/O pins are configured as digital PORTB = 0; // All PORTB pins are cleared TRISB = 0b00000010; // All PORTB pins except PORTB.1 are configured as outputs RBPU = 0; // Pull-up resistors are enabled WPUB1 = 1; // Pull-up resistor is connected to the PORTB.1 pin IOCB1 = 1; // The PORTB.1 pin may cause an interrupt on logic state change RBIE = GIE = 1; // Interrupt is enabled. PIN RB0/INT The RB0/INT pin is the only ‘true’ external interrupt source. It can be configured to react to signal raising edge (zero-to-one transition) or signal falling edge (one-to-zero transition). The INTEDG bit of the OPTION_REG register selects the appropriate signal. RB6 AND RB7 PINS The PIC16F887 does not have any special pins for programming (the process of writing a program to ROM).

Port pins, normally available as general-purpose I/O pins, are used for this purpose. To be more precise, it is about port B pins used for clock (RB6) and data transfer (RB7) during program loading. Besides, it is necessary to apply power supply voltage Vdd (5V) as well as appropriate voltage Vpp (12-14V) for FLASH memory programming.

During programming, Vpp voltage is applied to the MCLR pin. You don’t have to think of all details concerning this process, nor which one of these voltages is applied first since the programmer’s electronics is in charge of that. What is very important here is that the program may be loaded to the microcontroller even after soldering it onto the target device.

Normally, the loaded program can also be changed in the same way. This function is called ICSP ( In-Circuit Serial Programming). In order to use it properly, it is necessary to plan ahead. A piece of cake! It is only necessary to install a miniature 5-pin connector onto the target device so as to provide the microcontroller with necessary programming voltages. In order to prevent these voltages from interfering with other device electronics connected to microcontroller pins, all additional peripheral devices should be disconnected during the process of programming using resistors or jumpers. Similar to ports A and B, three pins can be configured as analog inputs in this case.

The ANSELH register bits determine whether a pin will act as an analog input (AN) or digital input/output: RE0 = AN5 (determined by the ANS5 bit of the ANSELregister); RE1 = AN6 (determined by the ANS6 bit of the ANSELregister); and RE2 = AN7 (determined by the ANS7 bit of the ANSELregister). Let's do it in mikroC. /* The PORTE.0 pin is configured as an analog input while another three pins of the same port are configured as digital. ANSEL = 0b00100000; // The PORTE.0 pin is configured as analog ANSELH = 0; // All other I/O pins are configured as digital TRISE = 0b00000001; // All PORTE pins except PORTE.0 are configured as outputs PORTE = 0; // All PORTE pins are cleared. ANSEL and ANSELH register The ANSEL and ANSELH registers are used to configure the input mode of an I/O pin to analog or digital.

In Short You will probably never write a program which doesn't use ports so the effort you make to learn all about them will definately pay off. Anyway, they are probaly the simplest modules within the microcontroller. This is how they are used: • When designing a device, select a port through which the microcontroller will communicate to peripheral environment. If you use only digital inputs/outputs, select any port you want. If you intend to use some of the analog inputs, select the appropriate ports supporting such a pin configuration (AN0-AN13). • Each port pin may be configured as either input or output. Bits of the TRISA, TRISB, TRISC, TRISD and TRISE registers determine how the appropriate port pins- PORTA, PORTB, PORTC, PORTD and PORTE will act.

• If you use some of the analog inputs, it is first necessary to set the appropriate bits of the ANSEL and ANSELH registers at the beginning of the program. • If you use switches and push buttons as input signal source, connect them to port B pins because they have pull-up resistors. The use of these resistors is enabled by the RBPU bit of the OPTION_REG register, whereas the installation of individual resistors is enabled by bits of the WPUB register. • It is usually necessary to respond as soon as input pins change their logic state. Dataradio Integra Tr Software Testing. However, it is not necessary to write a program for checking pins’ logic state. It is far simpler to connect such inputs to the PORTB pins and enable an interrupt to occur on every voltage change.

Bits of the IOCB and INTCON registers are in charge of that. The PIC16F887 microcontroller has three completely separate timers/counters marked as TMR0, TMR1 and TMR2. If you want to learn more about them, read carefully this chapter.